Gas Furnace Do's and Don't

Do's

• Change the Air Filter Regularly

• Check the fan belt to proper tension and wear

• Check the fresh air intake grill

• Properly service the furnace before the start of the heating season

Don't

• If the spill switch trips do not bypass the safely control correct the venting problem.

• Over tighten the fan belts, belt should be just tight enough not to slip.

• Adjust the gas regulator pressure setting

• Block off fresh air intakes. ( If the furnace can't get it's own air, it will take yours)

What is Proper Service

Furnace Temperature Rise TD: Most Residential furnaces are designed to work with a 40°F -60°F Temperature Rise (Supply Air Temperature - Return Air Temperature ), check the name plate of your furnace for it's design temperature.

Stack Temperature: The temperature of the flue 18" from the furnace should be a least 225°F. If it is lower then this then the flue gas will drop below the dew point more it vents from the top of the chimney. This will cause condensation in the chimney. This moisture is very acidic and will quickly damage the chimney.

Gas Manifold Pressure: The pressure on the gas manifold determines how much fuel your furnace will burn. Even a slight change from the design pressure, can have a big effect on the performance of the furnace. This should only be tested by a licensed gas fitter, and at the original startup of the furnace. This test can also be done by clocking the gas meter, with only the furnace burners running.

Chimney Draft: The draft up the chimney should be at least -0.02" w.c. with all gas appliances running, all exhaust fans running. And all the windows and doors closed to the house. If the Draft is less then -0.02"w.c. additional Fresh air must be brought into the house. If the draft is greater than -0.05" can reduce the appliance efficiency by allowing the flue gases to pass to quickly through the heat exchanger.

CO Test exhaust: Test the flue gas for Carbon Monoxide. A properly setup burner should produce less than 10 PPM., high efficacy furnace will often produce more. If more than 50 PPM then the burners should be removed, cleaned and setup, If greater than 300 PPM, repairs must be done ASAP. If higher than 500 PPM the furnace must be shut down until repairs are made.

Visual Inspection of the heat exchanger: Visually check the interior and exterior of the heat exchanger wear possible. Most of the heat exchanger is hidden from view, but the area that can be seen is a good indicator of the rest of the heat exchanger. Older or suspicions heat exchanger can be tested by smoke, or sulfur or cutting in an inspection door. If the burner is producing CO then testing the supply air for CO can show a the presents of a crack.

Visual Inspection of the Vent Connector: Check the connector between the furnace and the chimney. Signs of moisture indicate additional problems, On signal walled pipe, try squeezing the vent connector to check for interior rusting, weak pipes should be replaced.

Visual Inspection of the Chimney: If your furnace is connected to a Masonry, then it should be have a metal liner, if not then remove the clean out to check for debris. Visually inspect the exterior of cracks. Check the interior tile liner, if the liner appears cracked then it must be relined. Metal Chimney are much more reliable, but if moisture can be seen on the vent connector then the metal chimney should be inspected.

Check blower operation. Check the blower for dirt buildup on the fan blades, wear in the blower and/or motor bearings. Pulley wear and alignment, belt tension and wear. Lubricate when and where required.

Combustion Fan Motor: Check the combustion fan for signs of rusting on the housing, check the for bearing wear on the motor.

Burner Operations: The furnace on a normal call for heat will start the combustion fan, if present, for 30 seconds before trying to light the pilot or main flame. Spark Igniters should light the pilot after a few sparks, HSI (Hot Surface Igniter ) will light the main flame directly, standing pilots will light the main flame. After the burner is lit, then the fan should start. 30 to 90 seconds later. The burner and fan should stay on until the thermostat is satisfied. Once the thermostat is satisfied, the burner should stop, and the fan should run until the furnace is cooled down. Once the fan stops it should stay off until the next call for heat.